Author: Răducu Ioan Ștefan

This project features a rechargeable air mouse, a handheld device that allows users to navigate a screen from a distance. It functions similarly to a standard mouse, featuring left and right-click buttons. However, the cursor is controlled by adjusting the device's angle and position. This creates a user experience similar to using a TV remote or a laser pointer.

The primary purpose of this device is to assist users during presentations. Beyond this, it serves a variety of other applications, such as interacting with digital whiteboards or operating a computer from across the room.

The inspiration for this project came while observing a professor using a laser pointer to highlight information on a projector. I realized I could develop a device that not only highlights but also allows the user to select text, draw, and navigate through slides.

These capabilities make the device ideal for professional presentations, creative tasks, and even free time activities.

The core of this project is the ESP32 DevKit V1 (WROOM-32D), featuring an integrated antenna for wireless communication. It interfaces with a computer via Bluetooth using the HID (Human Interface Device) protocol. For motion tracking, the microcontroller is connected to an MPU6050 (GY-521 module) using the I2C protocol.

The power system consists of a 3.7V LiPo battery connected to a TP4056 charging module. To meet the power requirements, an MT3608 step-up converter boosts the battery voltage to the 5V necessary for the ESP32 and the IMU. Additionally, the microcontroller is wired to monitor the battery's voltage levels in real-time.

User feedback and interaction are handled through LEDs, which display the battery status and operating mode, while buttons provide the main interface for computer interaction and power control.

• ESP32 DevKit V1 (WROOM-32D)
• MPU-6050 (GY-521 Module)
• 3.7V Li-ion Battery
• TP4056 Charging Module
• MT3608 Step-Up Module
• Perforated Boards
• 470uF and 100nF Capacitor
• 2x 100kOhm Resistors
• 5x 330Ohm Resistors
• 5x Colored LED's
• Wires

The circuit has a power assembly which has four power lines:

• GND
• VBAT Current battery voltage, after going trough the TP4056 Charger Module.
• 5V Stable 5V voltage after the TP4056 Charger Module is stepped up to 5V using the MT3608 Step-Up Module.
• VBAT_DIV The battery voltage divided using a 100k/100k voltage divider (to read safely using ADC).

The rest of the circuit is buttons and LEDs for GPIO (using PWM and Interrupts), MPU-6050 (GY-521 Module) IMU for inertial measurement (using I2C). For power stability a 420uF bulk capacitor is used. A 100nF capacitor is present for filtering the ADC battery voltage reading.

• Input Protection: All buttons are connected to Ground, utilizing the ESP32's internal pull-up resistors.
• Power Filtering: C1 (470µF) acts as a bulk capacitor for the 5V rail, while C2 (100nF) provides high-frequency decoupling for the 3.3V rail.
• ADC Usage: GPIO 34 is part of ADC1, ensuring it remains operational while Bluetooth connectivity is active.
• Battery Voltage Measurement: The battery voltage is measured using an ADC pin, trough a voltage divider. Even if the battery is rated 3.7V, it can reach up to 4.2V, which would burn the 3.3V rated pin.

The first hardware test used is LED illumination on battery power. It checks the power assembly, ESP32 and LED integrity and wiring. The second test was testing the buttons, displaying which button was pressed using UART (while the battery is disconnected). The wake button works accordingly. The third test was ADC reading trough the voltage divider. The test requires the battery being connected while the power assembly does not feed power to the ESP32. The wire connecting them was removed temporarily for this test. As we plug and unplug the battery, I could observe that the voltage rises to the expected voltage in one reading, slowly decreasing to zero after the battery is unplug. This test requires a hardware modification (one wire to disconnect) in order to work without risking burning either the project or the computer motherboard.

Coming Soon

Coming Soon

Coming Soon

Coming Soon

• 09.05.2026: The initial version of this page is available, posted the introduction, general description and the block schema.
• 11-12.05.2026: Finished soldering the power assembly part and the rest of the circuit separately. Tested the power assembly part using a multimeter successfully. Tested the LED's, buttons', IMU's and ADC voltage measurement connections using a simple script.
• 14-16.05.2026: Managed to connect the capacitors and finished soldering the power assembly to the ESP32. LED test ran using battery power. Strengthened weak wiring. The battery can now be disconnected using jumper wires (for debugging).
• 16.05.2026: Updated the hardware chapter of this page. The hardware is now complete and passes the basic tests.

• [1] Espressif Systems - Datasheet ESP32 (WROOM-32D)
• [2] InvenSense - Datasheet MPU-6050
• [3] PowerCore - Datasheet TP4056 (Charger)
• [4] Aerosemi - Datasheet MT3608 (Step-up)

Export to PDF