Differences
This shows you the differences between two versions of the page.
|
pm:prj2026:atoader:stefan.oprea1711 [2026/05/17 00:36] stefan.oprea1711 [Resurse software / scheme] |
pm:prj2026:atoader:stefan.oprea1711 [2026/05/17 01:04] (current) stefan.oprea1711 [Jurnal] |
||
|---|---|---|---|
| Line 123: | Line 123: | ||
| ==Etapa 1 de Hardware== | ==Etapa 1 de Hardware== | ||
| - | * Am conectat pe breadboard primele componente ale proiectului: placa ATmega328P Xplained Mini, modulul HX711 si display-ul OLED. | + | * Am lipit pe o placa de prototipare buck converterul si driverele ca sa aibe gnd si vcc comun de la baterie. |
| - | * Modulul HX711 este legat la load cell si la microcontroller prin pinii DAT si CLK, pentru citirea greutatii. | + | * Am lipit pini pe o placa de prototipare pe care am bagat-o in placuta pentru a putea lipi in continuare fire. |
| - | * Display-ul OLED este conectat prin I2C, pe pinii SDA si SCL, si a fost testat cu un mesaj simplu pe ecran. | + | * Am terminat de lipit tot ce era acolo dupa aproximativ 30 ore oneste de munca. |
| - | * In aceasta etapa am verificat separat ca partea de cantarire comunica prin UART si ca display-ul porneste corect. | + | * Am reusit sa ansamblez drona si sa cuprind tot inauntrul ei. |
| - | {{:pm:prj2026:atoader:monitor_hidratare_jurnal_1.jpeg?500|}} | + | * Momentan am reusit sa setez elicele in sensurile bune, deci se ridica de la sol, dar nu pentru mult timp, trebuie reglata software mult. |
| - | {{:pm:prj2026:atoader:monitor_hidratare_jurnal_2.jpeg?500|}} | + | {{:pm:prj2026:atoader:da.jpeg?500|}} |
| - | + | {{:pm:prj2026:atoader:smek.jpeg?500|}} | |
| - | {{:pm:prj2026:atoader:monitor_hidratare_jurnal_3.jpeg?500|}} | + | |
| Line 139: | Line 138: | ||
| ==== Resurse hardware ==== | ==== Resurse hardware ==== | ||
| - | * ATmega328PB Xplained Mini - documentatie Microchip: https://www.microchip.com/en-us/development-tool/ATMEGA328PB-XMINI | + | * **ATmega328PB Xplained Mini** documentatie Microchip: https://www.microchip.com/en-us/development-tool/ATMEGA328PB-XMINI |
| - | * Load Cell 5kg: https://www.drot.ro/platforma-arduino/1119-senzor-de-greutate-5-kg.html | + | * **Modul GY-521 (MPU6050)**: https://sigmanortec.ro/Modul-giroscopic-si-accelerometru-3-axe-GY-521-p126016326 |
| - | * Modul HX711: https://sigmanortec.ro/en/weight-reading-module-hx711-24ad-2-channels-3-5v | + | * **Driver MX1616H**: De la Victor din laborator |
| - | * Display OLED SSD1306 0.96": https://www.drot.ro/platforma-arduino/1569-ecran-oled-iic-i2c-0-96-alb-128-x-64.html | + | * **Motor coreless 8x20mm 3.7V**: https://sigmanortec.ro/en/mini-coreless-motor-20x85-1mm-shaft-50000rpm-37v |
| - | * Modul buzzer pasiv si butoane: https://sigmanortec.ro/en/passive-buzzer-mode | + | * **Modul NRF24**: https://www.sigmanortec.ro/en/nrf24l01-24ghz-wireless-transceiver-module |
| + | * **Modul ridicător tensiune 3.7V → 5V**: https://sigmanortec.ro/en/step-up-modules | ||
| + | * **Baterie LiPo 3.7V 95C 500mah**: https://www.emag.ro/baterie-r-line-gens-ace-tattu-500-mah-3-7-v-95-c-multicolor-taa5001s95jsl/pd/DP84FRMBM/ | ||
| ==== Resurse software / scheme ==== | ==== Resurse software / scheme ==== | ||
