Show page

Differences

This shows you the differences between two versions of the page.

--- pm:prj2022:imacovei:home_assist_station [2022/05/27 23:16]
ionut.iordache3010
+++ pm:prj2022:imacovei:home_assist_station [2022/05/27 23:20] (current)
ionut.iordache3010 [Software Design]
@@ Line 92: / Line 92: @@
 <code>
-This is preformatted code all spaces are preserved: like              <-this
+// Arduino Side Code
+#include <SD.h>                       // need to include the SD library
+#include <TMRpcm.h>                   // also need to include this library (used to create instance of TMRpcm)
+#include <SPI.h>                      // and this one too for SPI protocol
+#include "DHT.h"                      // temperature and humidity sensor library
+#include <Wire.h>                     // wire library
+#include <LiquidCrystal_I2C.h>        // liquid crystal with I2C library
+#include <SoftwareSerial.h>           // used to transmit data to ESP8266
+#define ultrasoundTrigger 4           // pin 4 used as output with ultrasonic sensor
+#define ultrasoundEcho 2              // pin 2 used as input with ultrasonic sensor
+#define smokeA0 A0                    // pin A0 used as input with air-quality gas sensor
+#define DHTPIN A1                     // pin A1 used as input with temp&hum(DHT11) sensor
+#define DHTTYPE DHT11                 // sensor type = DHT11
+#define SD_ChipSelectPin 10           // pin 10 used as Chip Select - CS with SD module
+#define SPEAKER_PIN 9                 // pin 9 used as speaker
+long duration;                        // variable for the duration of sound wave travel
+float ultrasoundDistance;             // variable for the distance measurement
+String strArduinoToESP;               // string to transmit from Arduino to ESP8266 NODEMCU
+DHT dht(DHTPIN, DHTTYPE);             // initialize DHT11 sensor
+LiquidCrystal_I2C lcd(0x27, 16, 2);   // set the LCD address to 0x27 for a 16 chars and 2 line display
+TMRpcm tmrpcm;                        // used by SD card to play sound
+SoftwareSerial espSerial(5, 6);       // RX & TX on pins 5 & 6
+void setup() {
+  Serial.begin(9600);
+  espSerial.begin(9600);//TODO
+  // Ultrasonic sensor logic
+  // Serial.println("Ultrasonic Sensor HC-SR04 Test");
+  pinMode(ultrasoundTrigger, OUTPUT); // Sets the trigPin as an OUTPUT
+  pinMode(ultrasoundEcho, INPUT); // Sets the echoPin as an INPUT
+  // Smoke sensor logic
+  //Serial.println(F("Smoke sensor test!"));
+  pinMode(smokeA0, INPUT);
+  // DHT11 sensor logic
+  //Serial.println(F("DHT11 sensor test!"));
+  dht.begin();
+  // LCD&I2C logic
+  lcd.init();                          // initialize the lcd
+  lcd.backlight();                     // Turn on backlight
+  // SDcard logic
+  tmrpcm.speakerPin = SPEAKER_PIN;     // speaker ouput pin 9
+  if(!SD.begin(SD_ChipSelectPin)) {    // check connection and return proper message
+  // Serial.println("SD fail");
+    return;
+  }
+  tmrpcm.setVolume(6);                 // set output volume on pin selected
+  tmrpcm.play("test.wav");             // play sound from file
+  delay(22000);
+  // Welcome message
+  lcd.setCursor(0, 0);                 // set cursor at top left
+  lcd.print("  Welcome Home  ");       // print string
+  lcd.setCursor(0, 1);                 // set cursor at top left
+  lcd.print("       SIR      ");       // print string
+  delay(3000);
+}
+void loop() {
+  delay(1500);                         // process to repeat every 3s (1.5s + 1.5s underneath)
+  // Serial.println("=========");
+  // Read from smoke sensor
+  int smokeVal = analogRead(smokeA0);
+  // Serial.print("Pin A0 smoke: ");
+  // Serial.print(smokeVal);
+  // Serial.println(" ppm");
+  // Read from temp&hum(DHT11) sensor
+  float h = dht.readHumidity();
+  float t = dht.readTemperature();
+  // Serial.print(F("Humidity: "));
+  // Serial.print(h);
+  // Serial.print(F(" % | Temperature: "));
+  // Serial.print(t);
+  // Serial.println(F(" C"));
+  // Clears the trigPin condition
+  digitalWrite(ultrasoundTrigger, LOW);
+  delayMicroseconds(2);
+  // Sets the trigPin HIGH (ACTIVE) for 10 microseconds
+  digitalWrite(ultrasoundTrigger, HIGH);
+  delayMicroseconds(10);
+  digitalWrite(ultrasoundTrigger, LOW);
+  // Reads the echoPin, returns the sound wave travel time in microseconds
+  duration = pulseIn(ultrasoundEcho, HIGH);
+  delay(1000);
+  // Calculating the distance
+  ultrasoundDistance = duration * 0.034 / 2; // Speed of sound wave divided by 2 (go and back)
+  // Displays the distance on the Serial Monitor
+  // Serial.print("Distance: ");
+  // Serial.print(distance);
+  // Serial.println(" cm");
+  // Print on LCD
+  lcd.setCursor(0, 0);                 // set cursor at top left
+  lcd.print("Hum: ");                  // print string
+  lcd.print(h);                        // humidity value
+  lcd.print(" %    ");                 // unit
+  // ---
+  lcd.setCursor(0, 1);                 // set cursor at left space on 2nd row
+  lcd.print("Temp: ");                 // print string
+  lcd.print(t);                        // temperature value
+  lcd.print(" C   ");                  // unit
+  // ---
+  delay(1500);
+  lcd.setCursor(0, 0);                 // set cursor at top left
+  lcd.print("Gas val: ");              // print string
+  lcd.print(smokeVal);                 // gas value
+  lcd.print(" ppm");                   // unit
+  // ---
+  lcd.setCursor(0, 1);                 // set cursor at left space on 2nd row
+  lcd.print("Dist: ");                 // print string
+  lcd.print(ultrasoundDistance);       // distance value
+  lcd.print(" cm");                    // unit
+  // Send data to ESP as a string
+  strArduinoToESP = strArduinoToESP + smokeVal + "," + h + "," + t + "," + ultrasoundDistance; //TODO am h si t ca float si in ex sunt int-uri
+  // Serial.println(strArduinoToESP);
+  espSerial.println(strArduinoToESP);  // transmit string to ESP8266
+  strArduinoToESP = "";                // reinitialize string value
+}
+</code>
+<code>
+// ESP8266 Side Code
+#define BLYNK_TEMPLATE_ID "TMPL3SY-JM6J"
+#define BLYNK_DEVICE_NAME "Blynk LED"
+#define BLYNK_AUTH_TOKEN "RkiSi9tnBfPHmic1gaBwiC9upodMfHy1"
+#define BLYNK_FIRMWARE_VERSION        "0.1.0"
+#define BLYNK_PRINT Serial
+//#define BLYNK_DEBUG
+#define APP_DEBUG
+// Uncomment your board, or configure a custom board in Settings.h
+//#define USE_SPARKFUN_BLYNK_BOARD
+//#define USE_NODE_MCU_BOARD
+//#define USE_WITTY_CLOUD_BOARD
+//#define USE_WEMOS_D1_MINI
+#include "BlynkEdgent.h"
+#include <SoftwareSerial.h>
+String strArduinoToESP;               // string received from Arduino to ESP8266 NODEMCU
+int smokeVal;
+float humVal, tempVal, ultrasoundVal;
+char rdata;                           // received character
+const int motorspeed_pin = D1;
+const int DIRA = D2;
+const int DIRB = D7;
+BLYNK_WRITE(V0)
+{
+  int pinValue = param.asInt();
+  digitalWrite(D5, pinValue);
+}
+BLYNK_WRITE(V5)
+{
+  int pinValue = param.asInt();
+  digitalWrite(D6, pinValue);
+}
+BLYNK_WRITE(V7)
+{
+  int pinValue = param.asInt();
+  if (pinValue == 1) {
+    digitalWrite(motorspeed_pin, HIGH);
+    digitalWrite(DIRA, HIGH);
+    digitalWrite(DIRB, LOW);
+  } else if (pinValue == 0) {
+    digitalWrite(motorspeed_pin, LOW);
+    digitalWrite(DIRA, LOW);
+    digitalWrite(DIRB, LOW);
+  }
+}
+void sendSensorsData() {
+  Blynk.virtualWrite(V1, smokeVal);
+  delay(200);
+  Blynk.virtualWrite(V2, humVal);
+  delay(200);
+  Blynk.virtualWrite(V3, tempVal);
+  delay(200);
+  Blynk.virtualWrite(V4, ultrasoundVal);
+  delay(200);
+}
+void setup()
+{
+  Serial.begin(9600);
+  delay(100);
+  pinMode(D5, OUTPUT);
+  pinMode(D6, OUTPUT);
+  pinMode(motorspeed_pin, OUTPUT);
+  pinMode(DIRA, OUTPUT);
+  pinMode(DIRB, OUTPUT);
+  BlynkEdgent.begin();
+  delay(2000);
+  edgentTimer.setInterval(1000L, sendSensorsData);
+}
+void loop() {
+  if (Serial.available() > 0 ) {
+    rdata = Serial.read();
+    strArduinoToESP = strArduinoToESP + rdata;
+    // Serial.print(rdata);
+    if ( rdata == '\n') {
+      // Serial.println(strArduinoToESP);
+      String l = getValue(strArduinoToESP, ',', 0);
+      String m = getValue(strArduinoToESP, ',', 1);
+      String n = getValue(strArduinoToESP, ',', 2);
+      String p = getValue(strArduinoToESP, ',', 3);
+      smokeVal = l.toInt();
+      humVal = m.toFloat();
+      tempVal = n.toFloat();
+      ultrasoundVal = p.toFloat();
+      // Serial.print("val: ");
+      // Serial.print(smokeVal);
+      // Serial.print(" | val: ");
+      // Serial.print(humVal);
+      // Serial.print(" | val: ");
+      // Serial.print(tempVal);
+      // Serial.print(" | val: ");
+      // Serial.print(ultrasoundVal);
+      // Serial.print(" | val: ");
+      // Serial.println(" |");
+      BlynkEdgent.run();
+      delay(1000);
+      edgentTimer.run();              // Initiates SimpleTimer
+      delay(1000);
+      strArduinoToESP = "";
+    }
+  }
+}
+String getValue(String data, char separator, int index)
+{
+    int found = 0;
+    int strIndex[] = { 0, -1 };
+    int maxIndex = data.length() - 1;
+    for (int i = 0; i <= maxIndex && found <= index; i++) {
+        if (data.charAt(i) == separator || i == maxIndex) {
+            found++;
+            strIndex[0] = strIndex[1] + 1;
+            strIndex[1] = (i == maxIndex) ? i+1 : i;
+        }
+    }
+    return found > index ? data.substring(strIndex[0], strIndex[1]) : "";
+}
 </code>
 ===== Rezultate Obţinute =====