Differences
This shows you the differences between two versions of the page.
|
pm:prj2022:apredescu:134 [2022/05/09 22:38] andrei_vlad.dinoci created |
pm:prj2022:apredescu:134 [2022/05/25 23:32] (current) andrei_vlad.dinoci [Bibliography/Resources] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Climatization System ====== | ====== Climatization System ====== | ||
| + | ===== Introduction ===== | ||
| + | ===== Dinoci Andrei-Vlad 1222B ===== | ||
| + | In this project I want to create a simple climatization system. The system will be composed out of a fan, an LCD screen and 2 buttons for setting the wanted temperature. | ||
| + | <note tip> | ||
| + | |||
| + | * The fan will be turned on when the temperature will go over the temperature set by the user via the 2 buttons and this temperature as well as the fan speed will be displayed on the screen. | ||
| + | * Purpose: To cool a room | ||
| + | | ||
| + | |||
| + | </note> | ||
| + | |||
| + | |||
| + | ===== General description ===== | ||
| + | |||
| + | {{:pm:prj2022:apredescu:electric1.png?600|}} | ||
| + | {{:pm:prj2022:apredescu:software2.png?600|}} | ||
| + | |||
| + | ===== Hardware Design ===== | ||
| + | |||
| + | |||
| + | {{:pm:prj2022:apredescu:tinker.png?800|}} | ||
| + | |||
| + | Parts List | ||
| + | *LCD screen | ||
| + | *Fan | ||
| + | *Buttons | ||
| + | *Breadboard | ||
| + | *Transistor | ||
| + | *Temperature sensor | ||
| + | ===== Software Design ===== | ||
| + | |||
| + | |||
| + | <note tip> | ||
| + | I used the Arduino IDE for this project. The base temperature is 17°C. After that, using the 2 buttons on the breadboard, the user can increase or decrease the value. Based on the difference between the ambient temperature and the set temperature, the fan will spin faster or slower, using pwm. | ||
| + | On the LCD display, there are printed the information about the temperature set by the user and also the fan speed. | ||
| + | |||
| + | **Librarii si biblioteci third-party** | ||
| + | * dht11.h for temperature sensor | ||
| + | * LiquidCrystal_I2C.h for the LCD display | ||
| + | * Wire.h for communicating with the I2C device on the back on the of the LCD | ||
| + | </note> | ||
| + | |||
| + | ===== Results ===== | ||
| + | |||
| + | {{:pm:prj2022:apredescu:results1.png?700|}} | ||
| + | {{:pm:prj2022:apredescu:results2.jpeg?700|}} | ||
| + | |||
| + | ===== Conclusions ===== | ||
| + | Given the fact that this was my first major Arduino project, I am pretty satisfied with the results | ||
| + | ===== Download ===== | ||
| + | {{:pm:prj2022:apredescu:climatization_system_dinoci_andrei.rar|}} | ||
| + | ===== Journal ===== | ||
| + | |||
| + | 26/05/22 -> finished wiki page | ||
| + | |||
| + | |||
| + | 23/05/22 -> finished project(software + hardware) | ||
| + | |||
| + | |||
| + | 27/04/22 -> parts arrived | ||
| + | |||
| + | |||
| + | 22/04/22 -> theme selection | ||
| + | |||
| + | |||
| + | ===== Bibliography/Resources ===== | ||
| + | |||
| + | [[https://components101.com/displays/16x2-lcd-pinout-datasheet | LCD Datasheet]] | ||
| + | |||
| + | [[https://www.elecrow.com/download/datasheet-l9110.pdf | Motor Datasheet]] | ||
| + | |||
| + | [[https://www.mouser.com/datasheet/2/758/DHT11-Technical-Data-Sheet-Translated-Version-1143054.pdf | Temperature Datasheet]] | ||
| + | |||
| + | |||
| + | <html><a class="media mediafile mf_pdf" href="?do=export_pdf">Export to PDF</a></html> | ||
| + | |||
| + | |||
