Differences
This shows you the differences between two versions of the page.
|
pm:prj2022:amocanu:alarma_distanta [2022/06/02 04:33] bogdan_florin.manda [Rezultate Obţinute] |
pm:prj2022:amocanu:alarma_distanta [2022/06/02 04:39] (current) bogdan_florin.manda [Descriere generală] |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| ===== Descriere generală ===== | ===== Descriere generală ===== | ||
| - | Senzorul va detecta apropierea unui obiect, in functie de distanta LED-ul va lumina in mod diferit, iar in cazul unei distante ce depaseste o anumita limita se va activa un sunet de alarma. | + | Senzorul va detecta apropierea unui obiect, in functie de distanta LED-ul va lumina in mod diferit, iar in cazul unei distante ce se incadreaza intr-o anumita limita (20cm) se va activa un sunet de alarma. |
| {{ :pm:prj2022:amocanu:diagrama_mb_alarma.png?300 |}} | {{ :pm:prj2022:amocanu:diagrama_mb_alarma.png?300 |}} | ||
| + | **Update:** | ||
| + | In functie de pozitia obstacolului o arma va fi indreptata spre zona corespunzatoare in interiorul celor 20cm. | ||
| ===== Hardware Design ===== | ===== Hardware Design ===== | ||
| Line 24: | Line 25: | ||
| {{ :pm:prj2022:amocanu:alarma_scheme.png?nolink&800 |}} | {{ :pm:prj2022:amocanu:alarma_scheme.png?nolink&800 |}} | ||
| - | ===== Software Design ===== | ||
| + | **Update:** | ||
| + | * Servomotor SG90 | ||
| - | <note tip> | + | Servomotorul trebuie legat la GND, 5V si pin. |
| - | Descrierea codului aplicaţiei (firmware): | + | Pinul folosit pentru servo este 8. |
| - | * mediu de dezvoltare (if any) (e.g. AVR Studio, CodeVisionAVR) | + | ===== Software Design ===== |
| - | * librării şi surse 3rd-party (e.g. Procyon AVRlib) | + | |
| - | * algoritmi şi structuri pe care plănuiţi să le implementaţi | + | |
| - | * (etapa 3) surse şi funcţii implementate | + | |
| - | </note> | + | |
| Mediu de dezvoltare: ArduinoIDE | Mediu de dezvoltare: ArduinoIDE | ||
| Line 67: | Line 65: | ||
| <html><p align="center"><iframe width="560" height="315" src="https://www.youtube.com/embed/dnYV-YlPwtw" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></p></html> | <html><p align="center"><iframe width="560" height="315" src="https://www.youtube.com/embed/dnYV-YlPwtw" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></p></html> | ||
| - | === Update === | + | **Update:** |
| <html><p align="center"><iframe width="560" height="315" src="https://www.youtube.com/embed/98xiA6FNDVU" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></p></html> | <html><p align="center"><iframe width="560" height="315" src="https://www.youtube.com/embed/98xiA6FNDVU" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></p></html> | ||
| === Final Look === | === Final Look === | ||
| - | {{:pm:prj2022:amocanu:arduino1.jpg?direct&100|}} | + | {{:pm:prj2022:amocanu:arduino1.jpg?direct&220|}} |
| - | {{:pm:prj2022:amocanu:arduino2.jpg?direct&100|}} | + | {{:pm:prj2022:amocanu:arduino2.jpg?direct&220|}} |
| - | {{:pm:prj2022:amocanu:arduino3.jpg?direct&100|}} | + | {{:pm:prj2022:amocanu:arduino3.jpg?direct&220|}} |
| ===== Concluzii ===== | ===== Concluzii ===== | ||
