Show page

Differences

This shows you the differences between two versions of the page.

--- pm:prj2022:agmocanu:ambilightsystem [2022/05/25 22:09]
andrei_ioan.dinca [Software Design]
+++ pm:prj2022:agmocanu:ambilightsystem [2022/05/27 21:08] (current)
andrei_ioan.dinca [Concluzii]
@@ Line 24: / Line 24: @@
 A pc with windows on it
+The electric scheme:
+{{:pm:prj2022:agmocanu:screenshot_2022-05-27_at_8.49.14_pm.png?200|}}
+{{:pm:prj2022:agmocanu:img_1475.jpeg?200|}}
 ===== Software Design =====
@@ Line 30: / Line 35: @@
 In the Arduino IDE we also use the Fastled library to help with the animations for our led strip.
 We also use an app called "Prismatik" to help connect our DIY ambilight system to the pc.
-<nowiki>
-#include "FastLED.h"
-#define NUM_LEDS 55
-#define BRIGHTNESS 255
-#define LED_TYPE WS2812B
-#define COLOR_ORDER RGB
-#define PIN_DATA 6
-#define baudrate 128000
-const uint16_t SerialTimeout  = 60;      // time before LEDs are shut off if no data
-CRGB leds[NUM_LEDS];
-uint8_t * ledsRaw = (uint8_t *)leds;
-// A 'magic word' (along with LED count & checksum) precedes each block
+The coding part can be found here: https://github.com/ogdinca/Ambilight-Project-MA
-// of LED data; this assists the microcontroller in syncing up with the
-// host-side software and properly issuing the latch. The host software
-// will need to generate a compatible header: immediately following the
-// magic word are three bytes: a 16-bit count of the number of LEDs
-// (high byte first) followed by a simple checksum value (high byte XOR low
-// byte XOR 0x55). LED data follows, 3 bytes per LED, in order R, G, B,
-// where 0 = off and 255 = max brightness.
-const uint8_t magic[] = {'D','i','n','c','a'};
-#define MAGICSIZE  sizeof(magic)
-// Check values are header byte
-#define HICHECK    (MAGICSIZE)
-#define LOCHECK    (MAGICSIZE + 1)
-#define CHECKSUM   (MAGICSIZE + 2)
-enum processModes_t {Header, Data} mode = Header;
-int currByte; // current byte
-int outPos;  // current byte index in the LED array
-int bytesRemaining;  // set by checksum
-unsigned long t, lastByteTime, lastWordTime;
-void headerMode();
-void dataMode();
-void timeouts();
-#ifdef SERIAL_FLUSH
-  #undef SERIAL_FLUSH
-  #define SERIAL_FLUSH while(Serial.available() > 0) { Serial.read(); }
-#else
-  #define SERIAL_FLUSH
-#endif
-#ifdef DEBUG_LED
-  #define ON  1
-  #define OFF 0
-  #define D_LED(x) do {digitalWrite(DEBUG_LED, x);} while(0)
-#else
-  #define D_LED(x)
-#endif
-#ifdef DEBUG_FPS
-  #define D_FPS do {digitalWrite(DEBUG_FPS, HIGH); digitalWrite(DEBUG_FPS, LOW);} while (0)
-#else
-  #define D_FPS
-#endif
-void setup(){
-	FastLED.setBrightness(BRIGHTNESS);
-  // Initial RGB flash for testing
-  LEDS.showColor(CRGB(255, 0, 0));
-  delay(500);
-  LEDS.showColor(CRGB(0, 255, 0));
-  delay(500);
-  LEDS.showColor(CRGB(0, 0, 255));
-  delay(500);
-  LEDS.showColor(CRGB(0, 0, 0));
-	Serial.begin(baudrate);
-	Serial.print("Dinca\n"); // Send initial magic word
-	lastByteTime = lastWordTime = millis(); // Set initial counters
-}
-void loop(){
-	t = millis(); // Save current time
-	// If there is new serial data
-	if((currByte = Serial.read()) >= 0){
-		lastByteTime = lastWordTime = t; // Reset timeout counters
-		switch(mode) {
-			case Header:
-				headerMode();
-				break;
-			case Data:
-				dataMode();
-				break;
-		}
-	}
-	else {
-		// No new data
-		timeouts();
-	}
-}
-void headerMode(){
-	static int headPos, hi, lo, chk;
-	if(headPos < MAGICSIZE){
-		// Check if magic word matches
-		if(currByte == magic[headPos]) {headPos++;}
-		else {headPos = 0;}
-	}
-	else{
-		// Magic word matches! Now verify checksum
-		switch(headPos){
-			case HICHECK:
-				hi = currByte;
-				headPos++;
-				break;
-			case LOCHECK:
-				lo = currByte;
-				headPos++;
-				break;
-			case CHECKSUM:
-				chk = currByte;
-				if(chk == (hi ^ lo ^ 0x55)) {
-					// Checksum looks valid. Get 16-bit LED count, add 1 and multiply by 3 for R,G,B
-					D_LED(1);
-					bytesRemaining = 3L * (256L * (long)hi + (long)lo + 1L);
-					outPos = 0;
-					memset(leds, 0, NUM_LEDS * sizeof(struct CRGB));
-					mode = Data;
-				}
-				headPos = 0; // Reset header position regardless of checksum result
-				break;
-		}
-	}
-}
-void dataMode(){
-	// If LED data is not full
-	if (outPos < sizeof(leds)){
-		ledsRaw[outPos++] = currByte; // Issue next byte
-	}
-	bytesRemaining--;
-	if(bytesRemaining == 0) {
-		mode = Header; // Begin next header search
-		FastLED.show();
-		D_FPS;
-		D_LED(0);
-		SERIAL_FLUSH;
-	}
-}
-void timeouts(){
-	if((t - lastWordTime) >= 1000) {
-		Serial.print("Dinca\n"); // Send magic word to host
-		lastWordTime = t; // Reset counter
-		// If no data received for an extended time, turn off all LEDs.
-		if(SerialTimeout != 0 && (t - lastByteTime) >= (uint32_t) SerialTimeout * 1000) {
-			memset(leds, 0, NUM_LEDS * sizeof(struct CRGB));
-			FastLED.show();
-			mode = Header;
-			lastByteTime = t; // Reset counter
-		}
-	}
-}
-</nowiki>
 ===== Rezultate Obţinute =====
+[[https://youtu.be/FYe08aQorA4|Video Results]]
 ===== Concluzii =====
+Desi nu a mers cum mi-am dorit într-un final, rezultatul se apropie foarte mult de cel pe care îl așteptam.
 ===== Download =====
@@ Line 209: / Line 47: @@
 ===== Jurnal =====
-(Inca aștept sa îmi vina toate componentele comandate)
+.05.2022 Încă nu merge proiectul cum ar trebui
 ===== Bibliografie/Resurse =====