Show page

Differences

This shows you the differences between two versions of the page.

--- pm:prj2022:agmocanu:ambilightsystem [2022/05/25 22:04]
andrei_ioan.dinca [Software Design]
+++ pm:prj2022:agmocanu:ambilightsystem [2022/05/27 21:08] (current)
andrei_ioan.dinca [Concluzii]
@@ Line 24: / Line 24: @@
 A pc with windows on it
+The electric scheme:
+{{:pm:prj2022:agmocanu:screenshot_2022-05-27_at_8.49.14_pm.png?200|}}
+{{:pm:prj2022:agmocanu:img_1475.jpeg?200|}}
 ===== Software Design =====
@@ Line 31: / Line 36: @@
 We also use an app called "Prismatik" to help connect our DIY ambilight system to the pc.
-////
-#include "FastLED.h"
-#define NUM_LEDS 55
-#define BRIGHTNESS 255
-#define LED_TYPE WS2812B
-#define COLOR_ORDER RGB
-#define PIN_DATA 6
-#define baudrate 128000
-const uint16_t SerialTimeout  = 60;      // time before LEDs are shut off if no data
-CRGB leds[NUM_LEDS];
-uint8_t * ledsRaw = (uint8_t *)leds;
-// A 'magic word' (along with LED count & checksum) precedes each block
+The coding part can be found here: https://github.com/ogdinca/Ambilight-Project-MA
-// of LED data; this assists the microcontroller in syncing up with the
-// host-side software and properly issuing the latch. The host software
-// will need to generate a compatible header: immediately following the
-// magic word are three bytes: a 16-bit count of the number of LEDs
-// (high byte first) followed by a simple checksum value (high byte XOR low
-// byte XOR 0x55). LED data follows, 3 bytes per LED, in order R, G, B,
-// where 0 = off and 255 = max brightness.
-const uint8_t magic[] = {'D','i','n','c','a'};
-#define MAGICSIZE  sizeof(magic)
-// Check values are header byte
-#define HICHECK    (MAGICSIZE)
-#define LOCHECK    (MAGICSIZE + 1)
-#define CHECKSUM   (MAGICSIZE + 2)
-enum processModes_t {Header, Data} mode = Header;
-int currByte; // current byte
-int outPos;  // current byte index in the LED array
-int bytesRemaining;  // set by checksum
-unsigned long t, lastByteTime, lastWordTime;
-void headerMode();
-void dataMode();
-void timeouts();
-#ifdef SERIAL_FLUSH
-  #undef SERIAL_FLUSH
-  #define SERIAL_FLUSH while(Serial.available() > 0) { Serial.read(); }
-#else
-  #define SERIAL_FLUSH
-#endif
-#ifdef DEBUG_LED
-  #define ON  1
-  #define OFF 0
-  #define D_LED(x) do {digitalWrite(DEBUG_LED, x);} while(0)
-#else
-  #define D_LED(x)
-#endif
-#ifdef DEBUG_FPS
-  #define D_FPS do {digitalWrite(DEBUG_FPS, HIGH); digitalWrite(DEBUG_FPS, LOW);} while (0)
-#else
-  #define D_FPS
-#endif
-void setup(){
-	FastLED.setBrightness(BRIGHTNESS);
-  // Initial RGB flash for testing
-  LEDS.showColor(CRGB(255, 0, 0));
-  delay(500);
-  LEDS.showColor(CRGB(0, 255, 0));
-  delay(500);
-  LEDS.showColor(CRGB(0, 0, 255));
-  delay(500);
-  LEDS.showColor(CRGB(0, 0, 0));
-	Serial.begin(baudrate);
-	Serial.print("Dinca\n"); // Send initial magic word
-	lastByteTime = lastWordTime = millis(); // Set initial counters
-}
-void loop(){
-	t = millis(); // Save current time
-	// If there is new serial data
-	if((currByte = Serial.read()) >= 0){
-		lastByteTime = lastWordTime = t; // Reset timeout counters
-		switch(mode) {
-			case Header:
-				headerMode();
-				break;
-			case Data:
-				dataMode();
-				break;
-		}
-	}
-	else {
-		// No new data
-		timeouts();
-	}
-}
-void headerMode(){
-	static int headPos, hi, lo, chk;
-	if(headPos < MAGICSIZE){
-		// Check if magic word matches
-		if(currByte == magic[headPos]) {headPos++;}
-		else {headPos = 0;}
-	}
-	else{
-		// Magic word matches! Now verify checksum
-		switch(headPos){
-			case HICHECK:
-				hi = currByte;
-				headPos++;
-				break;
-			case LOCHECK:
-				lo = currByte;
-				headPos++;
-				break;
-			case CHECKSUM:
-				chk = currByte;
-				if(chk == (hi ^ lo ^ 0x55)) {
-					// Checksum looks valid. Get 16-bit LED count, add 1 and multiply by 3 for R,G,B
-					D_LED(1);
-					bytesRemaining = 3L * (256L * (long)hi + (long)lo + 1L);
-					outPos = 0;
-					memset(leds, 0, NUM_LEDS * sizeof(struct CRGB));
-					mode = Data;
-				}
-				headPos = 0; // Reset header position regardless of checksum result
-				break;
-		}
-	}
-}
-void dataMode(){
-	// If LED data is not full
-	if (outPos < sizeof(leds)){
-		ledsRaw[outPos++] = currByte; // Issue next byte
-	}
-	bytesRemaining--;
-	if(bytesRemaining == 0) {
-		mode = Header; // Begin next header search
-		FastLED.show();
-		D_FPS;
-		D_LED(0);
-		SERIAL_FLUSH;
-	}
-}
-void timeouts(){
-	if((t - lastWordTime) >= 1000) {
-		Serial.print("Dinca\n"); // Send magic word to host
-		lastWordTime = t; // Reset counter
-		// If no data received for an extended time, turn off all LEDs.
-		if(SerialTimeout != 0 && (t - lastByteTime) >= (uint32_t) SerialTimeout * 1000) {
-			memset(leds, 0, NUM_LEDS * sizeof(struct CRGB));
-			FastLED.show();
-			mode = Header;
-			lastByteTime = t; // Reset counter
-		}
-	}
-}
-////
 ===== Rezultate Obţinute =====
+[[https://youtu.be/FYe08aQorA4|Video Results]]
 ===== Concluzii =====
+Desi nu a mers cum mi-am dorit într-un final, rezultatul se apropie foarte mult de cel pe care îl așteptam.
 ===== Download =====
@@ Line 209: / Line 47: @@
 ===== Jurnal =====
-(Inca aștept sa îmi vina toate componentele comandate)
+.05.2022 Încă nu merge proiectul cum ar trebui
 ===== Bibliografie/Resurse =====