Differences
This shows you the differences between two versions of the page.
|
cns:laboratoare:laborator-10 [2013/01/14 14:18] traian.popeea [Topology] |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Lab 10 - MPLS VPN ====== | ||
| - | ===== Topology ===== | ||
| - | {{ :cns:resurse:lab10_cns.png?direct&800 }} | ||
| - | ===== Interfaces ===== | ||
| - | ^ Device ^ Interface ^ IP Address ^ Subnet Mask ^ | ||
| - | | CE1 | F0/0 | 10.1.1.1 | 255.255.255.252 | | ||
| - | | CE1 | Lo0 | 199.0.0.1 | 255.255.255.255 | | ||
| - | | PE1 | F0/0 | 10.1.1.2 | 255.255.255.252 | | ||
| - | | PE1 | S1/0 | 192.168.1.1 | 255.255.255.252 | | ||
| - | | PE1 | Lo0 | 150.0.1.1 | 255.255.255.255 | | ||
| - | | P | S1/0 | 192.168.1.2 | 255.255.255.252 | | ||
| - | | P | S1/1 | 192.168.1.5 | 255.255.255.252 | | ||
| - | | P | Lo0 | 150.0.1.2 | 255.255.255.255 | | ||
| - | | PE2 | F0/0 | 10.1.1.6 | 255.255.255.252 | | ||
| - | | PE2 | S1/1 | 192.168.1.6 | 255.255.255.252 | | ||
| - | | PE2 | Lo0 | 150.0.1.3 | 255.255.255.255 | | ||
| - | | CE2 | F0/0 | 10.1.1.5 | 255.255.255.252 | | ||
| - | | CE2 | Lo0 | 99.0.0.1 | 255.255.255.255 | | ||
| - | |||
| - | |||
| - | ===== Tasks ===== | ||
| - | Extract the [[http://ocw.cs.pub.ro/courses/_media/cns/laborator/lab10_cns_topology.zip| Lab10_CNS_Topology.zip]] file. | ||
| - | - [0p] Verify hostnames and IP addresses to all routers, according to the given topology. | ||
| - | - [+1=1p] Activate OSPF in the provider’s network. Run OSPF only on the interfaces between PE1, P and PE2 and on each provider router’s loopback interface. | ||
| - | - [+1=2p] Enable MPLS on the physical interfaces in the provider’s network. Do not run MPLS on interfaces facing customer routers (CE1 and CE2). | ||
| - | - [+3=5p] Create a VRF on both PE routers and bind them to the proper interfaces. Use the following parameters: | ||
| - | - VRF name: Client | ||
| - | - Route distinguisher: 1001:1 | ||
| - | - Route-targets for import and export: 64512:1 | ||
| - | - [+3=8p] Configure an MPBGP neighbor relationship between the PE routers. Establish neighbor relationships using the loopback addresses of PE1 and PE2. | ||
| - | - AS number for BGP: 64512 | ||
| - | - [+2=10p] Enable RIPv2 between the CE routers and PE routers. Advertise both customer loopbacks in RIP and check each CE router for propagated routes. | ||
| - | - [+1=11p] Using Wireshark capture traffic between P - PE1 and PE1 - CE1. | ||
