In our basic topology scenario, due to small budget our company still uses the old Cisco equipment for routing and filtering, but this time the second branch closed and added instead a visitor network (may be used by people that come at interview). After seeing some attacks done in our internal network like DoS, we decided to test different approaches: started with TCP intercept, continuing with CBAC and in the end implemented successfully the better security solution - zone based firewall (ZBF).

The new end-point machine called kali is a Kali Linux version 2019.3 and represents the possible attacker. The old network from branch 2 is reused (3.3.3.0/24) for visitors - with the first IP from subnet assigned to router and the second one for end-device. Note that we may refer to the router as firewall during the course of the lab.

Again, the router model is 7200 (version: c7200-adventerprisek9-mz.124-9.T4 - link here).

You have to do the following:

- add IPs for network between the server and the network equipment (use range 1.1.1.0/24)

- add IPs for network between the client and kali and the network equipment (use ranges 2.2.2.0/24 and 3.3.3.0/24) First IP is allocated for router and the second one for client1/kali machine

- add routes to make sure the endpoints can ping each other

Topology:

This first scenario is just for getting used to DoS attacks in our topology and hping3 command. Suppose that an attacker (called Trudy) wants to make a server unavailable using a SYN flood attack (which is fairly easy to create). This is done by sending TCP segments with SYN flag and no intention to complete the handshake. The server hangs by waiting for these connections to be finished until the timeout expires, but creates problems with legitimate TCP connections which can be denied.

TCP intercept is a features found in IOS that is used for SYN flood protection. There are 2 modes of protection:

- intercept: the router does mitm by intercepting the user's connection request and pretends to be the server, by completing the connection. Only if the 3-way handshake is completed successfully, the second TCP connection is set with the server.

Note: This process is transparent to both server and client

Suppose a SYN flood attack happens. The router has a buffer for all opened connections on behalf of client, that will timeout after a period of time (it sends to client a RST) due to no completed 3-way handshake and removed from the connection table. By using this approach, the server remains unaffected by the attack and valid requests are answered.

- watch: the disadvantage of intercept is that most of the times the router does this mitm for fair clients and adds overhead. A solution can be watch mode, which is a reactive approach that is monitoring connections, keeping track of half-open ones. Again, after a timeout (default 30 seconds) if a connection is not completed, the router sends a RST to server to remove it. This will remove all unwanted incompleted connections and allows legitimate ones to complete.

In this lab, we will use hping3 to simulate the attack. On server machine we have SimpleHTTPServer up and running on port 8080.

For TCP intercepting, we need firstly to add on router an ACL to permit tcp for any ip:

cisco_7200(config)#ip access-list extended TCP_INTERCEPT
cisco_7200(config-ext-nacl)#permit tcp any host 1.1.1.2 eq 8080

Enable TCP intercept in global config mode and specify the traffic to be analyzed (using ACL from above):

cisco_7200(config)#ip tcp intercept list TCP_INTERCEPT

The default mode is intercept, which is the one we are goind to use here. To change it to watch:

cisco_7200(config)#ip tcp intercept mode watch

Note that a mix of them is not possible.

There are also 3 timeouts that can be also configured: watch (default 30 secs - waiting time for 3-way handshake to complete), finrst (default 5 secs - waiting time for a connection to finish) and connection (default 24 hours - the maximum time of connection management. This is for sure one with handshake completed, but it can be in idle mode).

A high and low threshold values can be configured to deal with a big number of requests. After the high value is reached, it begins to drop connections until the low one. Default for high is 1100 and for low 900. To set them in production, you need careful baseline analysis to avoid dropping legitimate connections. These can be changed using:

cisco_7200(config)#ip tcp intercept max-incomplete high 100
cisco_7200(config)#ip tcp intercept max-incomplete low 10

The default method in aggressive mode is to drop oldest connections first until the connections number is below the minimum value. This can be also changed to random:

cisco_7200(config)#ip tcp intercept drop-mode random 

Let's stress the webserver using hping3 command:

root@kali:# hping3 -n -c 1000 -d 120 -S -w 64 -p 8080 --flood 1.1.1.2 

Explanations for the flags used:

1. -n = numeric output only (no lookup is done for host names)
2. -c 1000 = number of packets to send
3. -d 120 = size of each packet to target machine
4. -S = send SYN only (SYN attack)
5. -w 64 = TCP window size
6. -p 80 = port 80 (http)
7. –flood = send packets as fast as possible without taking care about the replies

Monitor the connections on router device (see that all are marked as incomplete):

cisco_7200#sh tcp intercept connections 
Incomplete:
Client                Server                State    Create   Timeout  Mode
3.3.3.2:47922         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47923         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47920         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47921         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47926         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47927         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47924         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47925         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47930         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47931         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
3.3.3.2:47928         1.1.1.2:8080          SYNRCVD  00:00:00 00:00:00 I
[...]

*Oct 29 02:29:33.847: %TCP-6-INTERCEPT: getting aggressive, count (1100/1100) 1 min 0

See that each conn has SYNRCVD state, because a SYN-ACK was sent by the router and the mode is I (intercept).

Note that this will drop any other connection request sent to server (in our case, there were generated ~500k in few secs, but only 1100 left for analysis). This can be seen here:

cisco_7200#sh tcp intercept statistics 
Intercepting new connections using access-list TCP_INTERCEPT
1100 incomplete, 0 established connections (total 1100)

After 1 minute, the connections will drop until low value and the rest are retransmitted to client with SYN+ACK until timeout (due to aggresive mode, the value is reduced by half):

cisco_7200#
*Oct 29 02:30:54.195: %TCP-6-INTERCEPT: calming down, count (0/900) 1 min 0

cisco_7200(config)#no ip tcp intercept list
cisco_7200(config)#no ip tcp intercept max-incomplete  high
cisco_7200(config)#no ip tcp intercept max-incomplete  low 

CBAC stands for Context-Based Access Control and represents a feature of Cisco products that is used for verifying protocol of application layer and dynamic modification of firewall rules that are based on it.

Using this feature, the number of connections opened by outside machines can be limited (to stop a DoS attack). This task proposes to create a CBAC rule that is used for monitoring TCP connections and added on outbound interface to UbuntuVM (traffic to that machine).

It provides 4 main functions:

- filtering traffic: TCP, UDP, ICMP connections. As seen on lab 1, ACLs can filter only at layers 3 and 4 and reflexive ones (RACL) at layer 5. CBAC can also inspect at application level.

- inspecting traffic: CBAC maintains its stateful firewall by looking at layer 7. It can also prevent SYN flood attacks by shutting connections down after a specific threshold is reached.

- detecting intrusions: DoS protection, limit phishing attacks.

- generate alerts and audits: it can generate real-time alerts and detect attacks. Logs can later be inspected

CBAC configuration steps:

Part 1: find which interface is external for router. In our case this is e1/0.

Part 2 [optional for us]: Before the traffic gets inspected by CBAC, the traffic must be permitted by ACLs. In our case, there are no ACLs added to simplify the usage.

Try now to access the webserver from client1 and kali. It should work.

Part 3: global timeout values for tcp, udp, icmp can also be changed (like synwait-time, finwait-time, idle-time etc.). Another value that can be changed is the maximum number of incomplete connections:

cisco_7200(config)#ip inspect tcp max-incomplete host 4 block-time 1

Part 4: port application mapping (PAM) - used to determine which type of inspection to perform on a connection. Example: for SMTP is 25 and CBAC knows that is email and what kinds of commands are exchanged.

There are multiple default mappings on ios:

cisco_7200#sh ip port-map 
Default mapping:  snmp                 udp port 161                        system defined
Default mapping:  echo                 tcp port 7                          system defined
[...]

You can also create nonstandard ones, like 8080 in our case or a host-specific one (for example: there are 2 machines listening on port 4444, but I want only the first one to be inspected).

We can create here for 1.1.1.2:8080 - this will do http inspection:

cisco_7200(config)#ip port-map http port 8080 list 1
cisco_7200(config)#access-list 1 permit 1.1.1.2

Part 5: create the inspection rules to filter the connections that are added to state table and what returning traffic is allowed back to client. If no rules are added, then all traffic is treated as usual.

We will use here inspection of http - mostly used when nonstandard ports are used (like us , 8080) or filter urls: Create firstly an inspect rule for tcp and apply it to an interface.

CISCO_7200(config)#ip inspect name INSPECT_TCP tcp alert on

Part 6: activate the rule on an interface

CISCO_7200(config)#int e1/0
CISCO_7200(config-if)#ip inspect INSPECT_TCP out

Part 7: troubleshooting From client1, ssh the server and see the sessions:

cisco_7200#sh ip inspect sessions 
Established Sessions
 Session 66180AB0 (2.2.2.2:39808)=>(1.1.1.2:22) tcp SIS_OPEN

A big drawback of the solution presented above is that it can become very complex when there is need to manage multiple interfaces. Also, it does not offer rules per host or network, all being bound to inbound or outbound traffic. Zone based firewall (or ZBF) is the next proposed security solution.

The model of ZBF is as following:

• each interface is part of a group, called zone
• traffic between zones is monitored by the device

ZBF allows the configuration of policies at a granular level, per protocol, host. Each policy can take one of these three actions:

• DROP action - DENY any traffic from moving between zones
• PERMIT action - ALLOW traffic to flow in a stateless manner (no monitor)
• INSPECT action - handle application sessions

The table from below summaries the actions taken by ZBF when monitoring traffic:

The configuration steps are as followed:

1. create the zones (add also a description in configuration mode for zone)
2. define the zone-pairs (a pair defined with source and destination zones)
3. define traffic classes (what type of traffic is of interest and allowed to pass the firewall)
4. define firewall policies (named policy maps on cisco routers)
5. assign policy maps to zone pairs
6. assign router interfaces to zones (this can be done also after the second step)

In the setup presented above, we will consider:

• KaliVM is in LAN zone
• UbuntuVM is in DMZ zone
• InternetVM is in PUBLIC zone (it has internet access)

A. Create zones on firewall:

CISCO_7200(config)#zone security LAN
CISCO_7200(config-sec-zone)#description Local Area Network
CISCO_7200(config-sec-zone)#exit   
CISCO_7200(config)#zone security DMZ
CISCO_7200(config-sec-zone)#description Public Servers Network
CISCO_7200(config-sec-zone)#exit
CISCO_7200(config)#zone security PUBLIC
CISCO_7200(config-sec-zone)#description Internet Access
CISCO_7200(config-sec-zone)#exit

B. Add the pairs between zones:

CISCO_7200(config)#zone-pair security LAN-TO-INTERNET source LAN destination PUBLIC    
CISCO_7200(config-sec-zone-pair)#exit
CISCO_7200(config)#zone-pair security LAN-TO-DMZ source LAN destination DMZ
CISCO_7200(config-sec-zone-pair)#exit
CISCO_7200(config)#zone-pair security PUBLIC-TO-DMZ source PUBLIC destination DMZ
CISCO_7200(config-sec-zone-pair)#exit

C. Go directly to step 6 and configure interfaces to each zones:

CISCO_7200(config)#int e1/0
CISCO_7200(config-if)#zone-member security DMZ
CISCO_7200(config)#int e1/1
CISCO_7200(config-if)#zone-member security  LAN
CISCO_7200(config-if)#int e1/2
CISCO_7200(config-if)#zone-member security PUBLIC

This will apply to zone-pairs defined above the default policy rule and all traffic is denied:

root@UbuntuVM:~# ping 10.20.20.2
PING 10.20.20.2 (10.20.20.2) 56(84) bytes of data.

^C
--- 10.20.20.2 ping statistics ---
7 packets transmitted, 0 received, 100% packet loss, time 6148ms

D. Define what type of traffic is of interest and should be allowed to pass the firewall. In our case, we would like to let our LAN members to access anything from Internet and DMZ, including TCP and ICMP.

CISCO_7200(config)#class-map type inspect match-any TCP-ICMP-CMAP
CISCO_7200(config-cmap)#match protocol tcp
CISCO_7200(config-cmap)#match protocol icmp

The class map from above is going to match any protocols defined within it OR match all of them. You can force some source IP addresses to match by using an ACL.

E. Define firewall policies: add to policy map the class map defined on point D)

CISCO_7200(config)#policy-map type inspect LAN-TO-INTERNET-PMAP
CISCO_7200(config-pmap)#class TCP-ICMP-CMAP
CISCO_7200(config-pmap-c)#inspect

F. Add to LAN-TO-INTERNET zone-pair the policy map:

CISCO_7200(config)#zone-pair security LAN-TO-INTERNET 
CISCO_7200(config-sec-zone-pair)#service-policy type inspect LAN-TO-INTERNET-PMAP

After sending successfully 2 icmp-echo-requests from KaliVM to InternetVM (from LAN to PUBLIC) - the traffic is allowed, the policy using is as follows:

CISCO_7200#show policy-map type inspect zone-pair 

policy exists on zp LAN-TO-INTERNET
 Zone-pair: LAN-TO-INTERNET

  Service-policy inspect : LAN-TO-INTERNET-PMAP

    Class-map: TCP-ICMP-CMAP (match-any)
      Match: protocol tcp
        0 packets, 0 bytes
        30 second rate 0 bps
      Match: protocol icmp
        1 packets, 64 bytes
        30 second rate 0 bps

   Inspect
        Packet inspection statistics [process switch:fast switch]
        icmp packets: [0:4]

        Session creations since subsystem startup or last reset 1
        Current session counts (estab/half-open/terminating) [1:0:0]
        Maxever session counts (estab/half-open/terminating) [1:1:0]
        Last session created 00:00:07
        Last statistic reset never
        Last session creation rate 1
        Maxever session creation rate 1
        Last half-open session total 0

    Class-map: class-default (match-any)
      Match: any 
      Drop
        0 packets, 0 bytes

See the match for protocol icmp (incremented with 1).

To allow access to DMZ for http (web servers) for LAN and PUBLIC zones, there is need to create a class-map for matching only HTTP traffic and a policy-map to allow data inspection.

Class map:

CISCO_7200(config)#class-map type inspect HTTP-ONLY-CMAP
CISCO_7200(config-cmap)#match protocol http

Policy map:

CISCO_7200(config)#policy-map type inspect HTTP-ONLY-PMAP
CISCO_7200(config-pmap)#class HTTP-ONLY-CMAP
CISCO_7200(config-pmap-c)#inspect 

Add policy-map to zone-pairs LAN-TO-DMZ and PUBLIC-TO-DMZ:

CISCO_7200(config)#zone-pair security LAN-TO-DMZ
CISCO_7200(config-sec-zone-pair)#service-policy type inspect HTTP-ONLY-PMAP
CISCO_7200(config-sec-zone-pair)#exit
CISCO_7200(config)#zone-pair security PUBLIC-TO-DMZ  
CISCO_7200(config-sec-zone-pair)#service-policy type inspect HTTP-ONLY-PMAP

This allows KaliVM (supposed for now to be a good person) and InternetVM to access HTTP service from DMZ zone (on UbuntuVM open a temporary service using: nc -k -l 80):

CISCO_7200#show policy-map type inspect zone-pair  PUBLIC-TO-DMZ

policy exists on zp PUBLIC-TO-DMZ
 Zone-pair: PUBLIC-TO-DMZ

  Service-policy inspect : HTTP-ONLY-PMAP

    Class-map: HTTP-ONLY-CMAP (match-all)
      Match: protocol http

   Inspect
        Packet inspection statistics [process switch:fast switch]
        tcp packets: [0:2]

        Session creations since subsystem startup or last reset 1
        Current session counts (estab/half-open/terminating) [0:0:0]
        Maxever session counts (estab/half-open/terminating) [0:1:0]
        Last session created 00:01:12
        Last statistic reset never
        Last session creation rate 0
        Maxever session creation rate 1
        Last half-open session total 0

    Class-map: class-default (match-any)
      Match: any 
      Drop
        0 packets, 0 bytes

However, this does not limit the number of tcp sessions opened. Using a session-filter, we can block more than X sessions opened (X=4 in this case, as it was for CBAC):

CISCO_7200(config)#parameter-map type inspect TCP-SYN-LIMIT
CISCO_7200(config-profile)#tcp max-incomplete host 4 block-time 1

Modify the policy-map to use inspect TCP-SYN-LIMIT:

CISCO_7200(config)#policy-map type inspect HTTP-ONLY-PMAP
CISCO_7200(config-pmap)#class HTTP-ONLY-CMAP
CISCO_7200(config-pmap-c)#inspect TCP-SYN-LIMIT

After this, we can start our DoS attack on KaliVM (now becomes again Trudy):

root@KaliVM:# hping3 -n -c 10 -w 64 -S -p 80 10.20.20.2
HPING 10.20.20.2 (eth0 10.20.20.2): S set, 40 headers + 0 data bytes
len=46 ip=10.20.20.2 ttl=63 DF id=0 sport=80 flags=SA seq=0 win=29200 rtt=31.6 ms
len=46 ip=10.20.20.2 ttl=63 DF id=0 sport=80 flags=SA seq=1 win=29200 rtt=14.9 ms
len=46 ip=10.20.20.2 ttl=63 DF id=0 sport=80 flags=SA seq=2 win=29200 rtt=22.8 ms
len=46 ip=10.20.20.2 ttl=63 DF id=0 sport=80 flags=SA seq=3 win=29200 rtt=21.9 ms

--- 10.20.20.2 hping statistic ---
10 packets transmitted, 4 packets received, 60% packet loss

Also, on router we can see some logs generated:

CISCO_7200(config-pmap-c)#
*Oct  8 22:24:35.163: %FW-4-HOST_TCP_ALERT_ON: (target:class)-(PUBLIC-TO-DMZ:HTTP-ONLY-CMAP):Max tcp half-open connections (4) exceeded for host 10.20.20.2
CISCO_7200(config-pmap-c)#
*Oct  8 22:24:35.167: %FW-2-BLOCK_HOST: (target:class)-(PUBLIC-TO-DMZ:HTTP-ONLY-CMAP):Blocking new TCP connections to host 10.20.20.2 for 1 minute (half-open count 4 exceeded).
CISCO_7200(config-pmap-c)#

For TCP intercept, change the mode to watch, high value for threshold to 100 and low to 10. Keep the list TCP_INTERCEPT.

Generate a new SYN flood attack from the kali machine and analyze the statistics and connections:

- are the threshold values used as configured and what is the state of connections ? [1p]

- capture on kali the RST packets using tcpdump (hint: 'tcp[13] & 4!=0' or 'tcp[tcpflags] == tcp-rst') and on server the SYN packets (hint: use 'tcp[13] & 2!=0'). Are SYN packets seen on server using watch mode ? [1p]

The server opened again port 4444 for chatting. Client1 wants to use it, but the attacker wants to initiate another SYN attack.

Change tcp intercept mode to intercept, keep the same threshold values, add to the same acl (TCP_INTERCEPT) a new entry for tcp port 4444. Then, start it using nc on server:

root@serverhq:/# nc -l 4444

And send tcp requests with SYN flag set from kali:

root@kali:~# hping3 -c 100 -n -S -p 4444 --faster 1.1.1.2 

Open the connection (before all entries expire - in 15 secs) from client1, send some messages and check the connection from router:

cisco_7200#sh tcp intercept connections 
Incomplete:
Client                Server                State    Create   Timeout  Mode
3.3.3.2:1886          1.1.1.2:4444          SYNRCVD  00:00:07 00:00:03 I
[...]
Established:
Client                Server                State    Create   Timeout  Mode
2.2.2.2:39056         1.1.1.2:4444          ESTAB    00:00:04 23:59:55 I

From server, check if it received client1's messages.